
*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*
                                    History
*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*
Modifications Summary between V2.00-B21 and V2.00-B43:
    *. When an invalid gateway address is entered into the web interface, 
       the switch responds with an invalid IP address error. 
    *. The web interface will allow the IP address to be set to 127.0.0.1, 
       which should not be valid.
    *. 0.0.0.0 should be accepted for the IP address and gateway address.  
        255.0.0.0 should be the minimum accepted for subnet mask.
        0.0.0.0 should be accepted as a valid IP address and gateway address.  
        For the IP address, selecting 0.0.0.0 should allow the user to completely 
        disable all remote administration of the switch, so that only the console 
        interface can be used to configure the switch.  For the gateway, 0.0.0.0 
        will allow the user to limit remote administration of the switch to the 
        local subnet.  For the subnet mask, class A (255.0.0.0) should be the minimum 
        allowed to be entered.  In addition, 0.0.0.0 should be the default for the IP 
        address and gateway, while 255.0.0.0 should be the default for the subnet mask.
    *. There are inconsistencies among the normal IP configuration, 
        the Boot menu IP configuration and the webinterface.
    *. Ctrl-T after savings settings will log you out
    *. B-2 Chip Gigabit port speed mode is assigned auto to "Auto" mode.
    *. Private MIB ¡V AgentIpIfEntry filtering check error : Can¡¦t filter 
       the IP such as "127.0.0.0".....
    *. 1. Do CLEAR COUNTER in Port Packet Error Statistics and Port Traffic Statistics
          menu will cause the console display error message. 
       2. Cannot clear counter in Port Traffic Statistics menu.
    *. Static Muticast filtering table should show not in use state ,
        for GMRP static muticast forwarding table exist a same muticast 
    *. SNMP --- "SwFdbStaticMemberEntry" oid return incorrect.
    *. Console in Browse Port-Based VLAN, cannot view next/previous page.
    *. Cannot clear counters in Port Packet Analysis menu.
    *. Cannot toggle when a field has invalid value.
    *. SNMP --- "MAC Address Age Time" item  not check value's range.(0~10000...)
    *. the copper ports only allow you to select auto or 1000mb.
    *. Port locking does not work correctly.
    *. Switch reboots while browsing address tbl.
    *. Address table lock is non functional.
    *. Removed the filtering entries from address table when browse address table.
    *. Change the default value of Address table lookup mode from Level 1 to Level 2.
    *. Don't allow normal users to view the community strings and trap receivers.
    *. Don't allow normal users to clear the history.
    *. Port config screen does not update when the port number is changed.
    *. here is no way to clear address table entries from SNMP.
    *. The total entries of "Browse Static Multicast Forwarding Table" will include the 
        entries of "delete on reset" and "delete on timeout."
    *. The GMRP delete-on-timeout will take effect.
    *. ifInError in MIB-II does not get updated.
    *. ifAdminStatus error.
    *. Asymmetric VLAN.
    *. Fixed Nway toggle issue in slot1, FX module.
    *. Address lock and set the address in the forwarding table to a port ,
        A PC with the address  change link to another port still can ping device.
    *. NV-RAM failed in debugging mode found by factory.
    *. Have a trunk garbage in console menu.
        Slot-1:One-port FX module.
        Slot-2:Two-port Giga module.
    *. Allow users to input 40 byte of community string.

*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*
